On this page
How to turn decimal inches into a fraction
- Multiply the decimal by the denominator you want (16 for sixteenths): 0.6 × 16 = 9.6.
- Round to a whole number: 10. That gives 10/16.
- Simplify: 10/16 = 5/8. So 0.6 in is about 5/8 in (0.625), 0.025 in (0.64 mm) too long.
The calculator does this for every precision at once and shows how far off each fraction is in millimetres, so you can see whether 1/16 is close enough or you need 1/32.
Inch fraction to decimal chart (1/64)
| Fraction | Decimal (in) | mm |
|---|---|---|
| 1/64″ | 0.015625 | 0.397 |
| 1/32″ | 0.03125 | 0.794 |
| 3/64″ | 0.046875 | 1.191 |
| 1/16″ | 0.0625 | 1.587 |
| 5/64″ | 0.078125 | 1.984 |
| 3/32″ | 0.09375 | 2.381 |
| 7/64″ | 0.109375 | 2.778 |
| 1/8″ | 0.125 | 3.175 |
| 9/64″ | 0.140625 | 3.572 |
| 5/32″ | 0.15625 | 3.969 |
| 11/64″ | 0.171875 | 4.366 |
| 3/16″ | 0.1875 | 4.762 |
| 13/64″ | 0.203125 | 5.159 |
| 7/32″ | 0.21875 | 5.556 |
| 15/64″ | 0.234375 | 5.953 |
| 1/4″ | 0.25 | 6.35 |
| 17/64″ | 0.265625 | 6.747 |
| 9/32″ | 0.28125 | 7.144 |
| 19/64″ | 0.296875 | 7.541 |
| 5/16″ | 0.3125 | 7.938 |
| 21/64″ | 0.328125 | 8.334 |
| 11/32″ | 0.34375 | 8.731 |
| 23/64″ | 0.359375 | 9.128 |
| 3/8″ | 0.375 | 9.525 |
| 25/64″ | 0.390625 | 9.922 |
| 13/32″ | 0.40625 | 10.319 |
| 27/64″ | 0.421875 | 10.716 |
| 7/16″ | 0.4375 | 11.112 |
| 29/64″ | 0.453125 | 11.509 |
| 15/32″ | 0.46875 | 11.906 |
| 31/64″ | 0.484375 | 12.303 |
| 1/2″ | 0.5 | 12.7 |
| 33/64″ | 0.515625 | 13.097 |
| 17/32″ | 0.53125 | 13.494 |
| 35/64″ | 0.546875 | 13.891 |
| 9/16″ | 0.5625 | 14.287 |
| 37/64″ | 0.578125 | 14.684 |
| 19/32″ | 0.59375 | 15.081 |
| 39/64″ | 0.609375 | 15.478 |
| 5/8″ | 0.625 | 15.875 |
| 41/64″ | 0.640625 | 16.272 |
| 21/32″ | 0.65625 | 16.669 |
| 43/64″ | 0.671875 | 17.066 |
| 11/16″ | 0.6875 | 17.462 |
| 45/64″ | 0.703125 | 17.859 |
| 23/32″ | 0.71875 | 18.256 |
| 47/64″ | 0.734375 | 18.653 |
| 3/4″ | 0.75 | 19.05 |
| 49/64″ | 0.765625 | 19.447 |
| 25/32″ | 0.78125 | 19.844 |
| 51/64″ | 0.796875 | 20.241 |
| 13/16″ | 0.8125 | 20.637 |
| 53/64″ | 0.828125 | 21.034 |
| 27/32″ | 0.84375 | 21.431 |
| 55/64″ | 0.859375 | 21.828 |
| 7/8″ | 0.875 | 22.225 |
| 57/64″ | 0.890625 | 22.622 |
| 29/32″ | 0.90625 | 23.019 |
| 59/64″ | 0.921875 | 23.416 |
| 15/16″ | 0.9375 | 23.813 |
| 61/64″ | 0.953125 | 24.209 |
| 31/32″ | 0.96875 | 24.606 |
| 63/64″ | 0.984375 | 25.003 |
Advertisement
Metric drill bits in inch fractions
| Metric | Inches | Nearest 1/64 | Off by |
|---|---|---|---|
| 1 mm | 0.0394 | 3/64″ | +0.19 mm |
| 1.5 mm | 0.0591 | 1/16″ | +0.09 mm |
| 2 mm | 0.0787 | 5/64″ | -0.02 mm |
| 2.5 mm | 0.0984 | 3/32″ | -0.12 mm |
| 3 mm | 0.1181 | 1/8″ | +0.17 mm |
| 3.5 mm | 0.1378 | 9/64″ | +0.07 mm |
| 4 mm | 0.1575 | 5/32″ | -0.03 mm |
| 4.5 mm | 0.1772 | 11/64″ | -0.13 mm |
| 5 mm | 0.1969 | 13/64″ | +0.16 mm |
| 5.5 mm | 0.2165 | 7/32″ | +0.06 mm |
| 6 mm | 0.2362 | 15/64″ | -0.05 mm |
| 6.5 mm | 0.2559 | 1/4″ | -0.15 mm |
| 7 mm | 0.2756 | 9/32″ | +0.14 mm |
| 8 mm | 0.315 | 5/16″ | -0.06 mm |
| 9 mm | 0.3543 | 23/64″ | +0.13 mm |
| 10 mm | 0.3937 | 25/64″ | -0.08 mm |
| 12 mm | 0.4724 | 15/32″ | -0.09 mm |
| 13 mm | 0.5118 | 33/64″ | +0.1 mm |
A plus sign means the inch bit is slightly larger than the metric size. For a tight fit, choose the bit that is not larger.
Reading fractions on a tape measure
Most US tape measures mark sixteenths: the longest line between inches is 1/2, then 1/4, 1/8 and the shortest 1/16. Count sixteenths from the last whole inch and simplify (6/16 = 3/8). Fine rulers and machinist scales go to 1/32 or 1/64.
Summary
Type decimal inches, mm, cm or feet, and get the nearest fraction from 1/2 to 1/64 with the error, or turn a fraction back into a decimal and mm; the 1/64 chart and metric drill table are below. Working with Japanese sizes? See the Japanese size converter or the quilt binding calculator.